MCS
MCS, 6-sp transmission main bearing installer tool
Used to install the main transmission case bearing OEM 8967, 8967A (MCS 921472). Tool will provide a correct bearing angle...
€289,67
In stock · ships today
MCS
MCS, flywheel holding tool
Used to insert the sprocket shaft, of the assembled flywheel assembly, into the tool. The tool is clamped in a...
€76,23
In stock · ships today
MCS
MCS, upper 41mm fork tube plug socket
Used to remove and install top fork tube plug that fits inside the fork tube. Prevents damage to the plugs...
€53,36
In stock · ships today
MCS
MCS, pinion bearing race removal tool
Used to remove the pinion bearing race / pinion shaft bushing (24599-58A/B, 24599-93) from the right side crankcase. Replacement for...
€38,12
In stock · ships today
MCS
MCS, Touring transmission oil drain spigot tool
Used to route the oil flow of the transmission, when changing the oil, straight into the oil drain pan. Prevents...
€18,30
In stock · ships today
MCS
MCS, main bearing end play tool
Used to simulate the sprocket shaft side of a flywheel so that the flywheel lateral end play can be measured...
€76,23
In stock · ships today
MCS
MCS, main bearing end play tool
Used to simulate the sprocket shaft side of a flywheel so that the flywheel lateral end play can be measured...
€76,23
In stock · ships today
MCS
MCS, 6-sp transmission door bearing tool
Used to install and remove transmission trapdoor bearings (8970 for Twin Cam and 8970A and 110000010 for M8) on 6-speed...
€152,46
In stock · ships today
MCS
MCS, fork seal & cap installer tool kit
Used to install fork seals and fork caps without damage to the seal lip. This tool can be used for...
€190,58
In stock · ships today
MCS
MCS, 6-sp transmission door puller tool
Used to pull the transmission door, complete with gears and shafts attached, from the transmission case. Does not damage door...
€125,78
In stock · ships today
MCS
MCS, inner balancer bearing install tool
Used to install the inner engine balancer bearing (8992A / MCS 507698) in the left case. Work can be done...
€186,76
In stock · ships today
MCS
MCS, 45A alternator rotor puller tool
Used to pull the alternator rotor from the sprocket shaft, without issues associated with strong magnets. Pulls simple and direct...
€114,35
In stock · ships today
MCS
MCS, balancer shaft alignment tool
Used to set-up correct alignment of the sprockets / balancer chain to insure maximum life and dependability from the balancer...
€190,58
In stock · ships today
MCS
MCS, sprocket shaft rotating socket tool
Used to rotate the crankshaft for timing or clearance checks. Fits the splines on the sprocket shaft. With a 1/2"...
€76,23
In stock · ships today
MCS
MCS, cam bearing remover tool
Used to pull the camshaft roller bearing (OEM 8990A) from the camshaft after camshafts are removed from support plate. Pulls...
€121,97
In stock · ships today
MCS
MCS, clutch hub puller
Used to pull the clutch hub from the mainshaft. Includes 4 bolts for dry clutch removal.
€76,23
Available to order
MCS
MCS, clutch adjusting tool
Deep socket design allows this socket to access the lock nut of the clutch adjuster. The hole allows final adjustment...
€13,72
In stock · ships today
MCS
MCS, bearing & exhaust seal service tool kit
Used to service wheel bearing races, steering head bearing races, sprocket shaft bearing race, cam bearing race and exhaust seals....
€228,69
In stock · ships today
MCS
MCS, rubber mount swingarm assembly tool
Used to remove and install the swingarm bushing assembly (also known as cleve blocks) (MCS 996483 / OEM 47556-81) found...
€190,58
In stock · ships today
MCS
MCS, 6-sp transmission main drive gear remove tool
Used to remove the transmission main drive gear from the main drive bearing on all 6-speed Big Twin models. Can...
€228,69
In stock · ships today
MCS
MCS, 6-sp transmission pulley nut socket
Used to install and remove the large 2-1/4" hex nut (35241-06, regular right hand threaded) that holds the rear drive...
€152,46
Available to order
MCS
MCS, V-Rod clutch plate alignment assembly tool
Used for correctly aligned clutch plates in the clutch shell during installation of the clutch plate pack.
€30,49
In stock · ships today
MCS
MCS, main drive gear seal install tool
Used to install main drive gear seal (OEM 12074, 12074A). Installs to the correct depth. Includes pilot for seal protection....
€91,48
Available to order
MCS
MCS, transmission pulley lock tool
Used to lock the transmission pulley (belt sprocket) when installing or removing the transmission pulley nut. Fits 4 & 5-speed...
€137,21
In stock · ships today
You've seen 912 of 1199 products
Show 24 more