MCS
MCS, valve spring compressor tool
Used to install and remove valve springs. Modern equivalent of the classic 96600-36 H-D style valve spring compressor. Note: Will...
€129,36
In stock · ships today
MCS
MCS, oil filter wrench RH/RA
Used to remove OEM style 62700280 spin-on oil filter on Revolution Max engines. Will also fit S&S oil filters 3/8"...
€27,90
Available to order
MCS
MCS Scan, connector slave cable. Euro 5 (6-pin)
For models equipped with a Euro V 6-pin diagnostic port. Used with MCS Scan 560041. Sold to dealers only. Note:...
€109,12
In stock · ships today
MCS
MCS, cylinder head holder. M12/M14
With M12x 1.25 and M14 x 1.25 threaded ends to hold the head in the spark plug hole. Tool can...
€16,80
In stock · ships today
MCS
MCS, cylinder head holder. M10/M12
With M10x 1.0 and M12 x 1.25 threaded ends to hold the head in the spark plug hole. Tool can...
€16,80
In stock · ships today
MCS
MCS, valve spring compressor tool set
Used to install and remove valve springs. Upgraded modern equivalent of the classic 96600-36 H-D style valve spring compressor. Comes...
€226,71
In stock · ships today
MCS
MCS, balancer shaft bearing tool
Used to pull and install engine balancer bearings from the case. Removal and installation can be done safely and professional...
€65,68
In stock · ships today
MCS
MCS, wristpin bushing driver tool
Used to install and remove new wristpin bushings without removing connecting rods from the crankcase. Removes and installs both bushings...
€60,99
In stock · ships today
MCS
MCS, magnetic tappet holder tool TC / M8
Used when removing the camshaft/s on Twin Cam or M8 engines. Tool installs over the tappet covers and will hold...
€49,01
In stock · ships today
MCS
MCS, 6-speed main drive gear bearing tool
Used to install main drive gear inner & outer bearing (8042A) on 6-speeds. Also installs main drive gear seal (12077)....
€87,12
In stock · ships today
MCS
MCS, pinion shaft bushing remover/installer tool
Removes and installs 25344-99 / 921146 pinion shaft bushing in the cam support plate. After 2010 these bushings are no...
€136,13
In stock · ships today
MCS
MCS, adapter compression tester. 12mm
Lost or broke your screw-on adapter for your compression tester? - Used between the tubing of a compression tester/leak down...
€54,45
In stock · ships today
MCS
MCS, hollow axle plug tool
Includes 2 plugs. Plugs into left & right side of axle and are used to find the correct center point,...
€53,36
In stock · ships today
MCS
MCS, wrist pin lock ring tool
Used to install spiral lock / Spiro lock (circular flat wire) style wristpin retaining rings to 0.535" ID wristpins. Easy...
€98,01
In stock · ships today
MCS
MCS, wrist pin lock ring tool
Used to install spiral lock / Spiro lock (circular flat wire) 22582-52 style wristpin retaining rings to 0.515" ID wristpins....
€98,01
In stock · ships today
MCS
MCS, rocker box alignment tool
Used to align rocker boxes correctly and prevents them from shifting when being tightened. Helps prevent misalignment that may cause...
€54,45
In stock · ships today
MCS
MCS, oil pump seal install tool
Used to install the oil pump seal into the oil pump housing, below gear surface. Prevents installation damage to seal.
€76,23
In stock · ships today
MCS
MCS, top dead center tool
5/8"-18 threaded. Installs in timing hole to find & hold the flywheel at correct top dead center for static timing...
€27,23
In stock · ships today
MCS
MCS, ignition switch remover tool
Used to remove the electrical connector without damage to the ignition switch.
€53,36
In stock · ships today
MCS
MCS, balancer bearing tool kit
Used to install & remove the outboard balancer bearing on chain guide support plate. Also installs a new balancer bearing...
€141,57
In stock · ships today
MCS
Motorcycle storehouse, 'Size it' bolt & nut gauge tool
Plastic. Yellow with black print. Used to identify bolt diameter of US bolts from #4 to 1" and Metric bolts...
€6,02
In stock · ships today
MCS
4-speed transmission stand. Black
Designed to be clamped in a vice, to provide excellent stability. Takes all stock 4-speed and custom 4 to 5-speed...
€41,61
In stock · ships today
MCS
Engine stand 45" side valve
Steel painted motor stand, designed to provides excellent stability when working on the engine.
€117,05
In stock · ships today
MCS
Engine stand Twin Cam B
Steel painted motor stand, designed to provides excellent stability when working on the engine.
€83,77
In stock · ships today
You've seen 864 of 1199 products
Show 24 more